[1] S.Hajiahmadi, M. Elyasi, M. Shakeri, Development a new methodology for measuring deep drawing forces based on dimensionless evaluation,
Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Vol. 235, No. 19, pp. 4057-4069, 2021.
https://doi.org/10.1177/0954406220969718
[2] R. Ghasemi, M. Elyasi, H. Baseri, M. J. Mirnia, Microstructural analysis of sheet hydroforming process assisted by radial ultrasonic punch vibration in a hydro-mechanical deep drawing die,
The International Journal of Advanced Manufacturing Technology, Vol. 125, No. 11-12, pp. 5359-5368, 2023.
https://doi.org/10.1007/s00170-023-11007-x
[3] A. H. Nikdooz, M. J. Mirnia, H. Baseri, Study of formability of aluminum truncated pyramid in single-stage and two-stage incremental sheet forming, Modares Mechanical Engineering, Vol. 16, No. 5, pp. 210-220, 2016. (in Persian)
[5] A. Attanasio, E. Ceretti, C. Giardini, L. Mazzoni, Asymmetric two points incremental forming: improving surface quality and geometric accuracy by tool path optimization,
Journal of materials processing technology, Vol. 197, No. 1-3, pp. 59-67, 2008.
https://doi.org/10.1016/j.jmatprotec.2007.05.053
[6] A. A. Nourmohammadi, M. Elyasi, M. J. Mirnia, Flexibility improvement in two-point incremental forming by implementing multi-point die,
The International Journal of Advanced Manufacturing Technology, Vol. 102, pp. 2933-2952, 2019.
https://doi.org/10.1007/s00170-019-03307-y
[7] M. Silva, P. Martins, Two-point incremental forming with partial die: theory and experimentation,
Journal of Materials Engineering and Performance, vol. 22, pp. 1018-1027, 2013.
https://doi.org/10.1007/s11665-012-0400-3
[8] V. Franzen, L. Kwiatkowski, G. Sebastiani, R. Shankar, A. Tekkaya, M. Kleiner, Dyna-die: towards full kinematic incremental forming,
International Journal of Material Forming, vol. 1, pp. 1163-1166, 2008.
https://doi.org/10.1007/s12289-008-0187-9
[9] S. Kurra, S. P. Regalla, Experimental and numerical studies on formability of extra-deep drawing steel in incremental sheet metal forming,
Journal of Materials Research and Technology, Vol. 3, No. 2, pp. 158-171, 2014.
https://doi.org/10.1016/j.jmrt.2014.03.009
[10] C. V. Ajay, C. Boopathi, P. Kavin, Incremental sheet metal forming (ISMF): A literature review, in
AIP Conference Proceedings, 2019, Vol. 2128, No. 1, pp. 030012: AIP Publishing LLC.
https://doi.org/10.1063/1.5117955
[12] S. Darzi, M. J. Mirnia, M. Elyasi, Single-point incremental forming of AA6061 aluminum alloy at elevated temperatures,
The International Journal of Advanced Manufacturing Technology, Vol. 116, No. 3-4, pp. 1023-1039, 2021.
https://doi.org/10.1007/s00170-021-07494-5
[13] H. Movahedinia, M. J. Mirnia, M. Elyasi, H. Baseri, An investigation on flaring process of thin-walled tubes using multistage single point incremental forming,
The International Journal of Advanced Manufacturing Technology, Vol. 94, pp. 867-880, 2018.
https://doi.org/10.1007/s00170-017-0971-0
[16] A. Taherkhani, A. Basti, N. Nariman-Zadeh, A. Jamali, Achieving maximum dimensional accuracy and surface quality at the shortest possible time in single-point incremental forming via multi-objective optimization,
Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 233, No. 3, pp. 900-913, 2019.
https://doi.org/10.1177/0954405418755822
[17] S. Scheffler, A. Pierer, P. Scholz, S. Melzer, D. Weise, Z. Rambousek, Incremental sheet metal forming on the example of car exterior skin parts,
Procedia Manufacturing, Vol. 29, pp. 105-111, 2019.
https://doi.org/10.1016/j.promfg.2019.02.112
[18] F. Maaß, M. Hahn, A. E. Tekkaya, Adjusting residual stresses by flexible stress superposition in incremental sheet metal forming,
Archive of Applied Mechanics, Vol. 91, pp. 3489-3499, 2021.
https://doi.org/10.1007/s00419-021-01929-x