Comparison of the effect of heat treatment quenching - partitioning (Q-P) and direct quenching (D-Q) on the microstructure and mechanical properties of a high strength steel containing Ti microalloy

Document Type : Original Article

Authors

Faculty of Mechanical Engineering, University Tabriz, Tabriz, Iran

Abstract

Quenching-partitioning (Q-P) is one of the methods of producing advanced high strength steels (AHSS). The principles of the mentioned thermal process are based on carbon penetration from martensite to residual austenite (γR) and stabilization of γR. In this research, the alloy with the chemical composition of 0.054 wt% Al, 1.5 wt% Si, 2.2 wt% Mn, 2.2 wt% Mn, 0.21 wt% Fe, containing 0.08% Ti as a micro-alloy in an induction melting furnace in VIM was cast as an ingot. The said ingot was homogenized for 3 hours at a temperature of 1200 °C. The homogenized ingot was rolled into a sheet with a thickness of 1.5 mm by hot and cold rolling processes. The prepared sheet was subjected to Q-P heat treatment and direct quenching (D-Q) and was compared in terms of microstructure and mechanical properties. The comparison of the effect of the mentioned operations on the microstructure and mechanical properties of steel was done by scanning electron microscope (SEM), X-ray analysis (XRD), micro-hardness measurement, and metallography. The obtained results showed that the sample subjected to Q-P heat treatment has better formability and strength than the D-Q sample. The strength and formability of the sample obtained from Q-P were reported as 1062 MPa and 24.52% respectively, and the strength and formability of the sample obtained from D-Q were reported as 1484 MPa and 15.21% respectively.

Keywords

References

[1] Edmonds, D.V., He, K., Rizzo, F.C., De Cooman, B.C., Matlock,D.K. and Speer, J.G., “Quenching and partitioning martensite—A novel steel heat treatment”, Materials Science and Engineering A, Vols. 438-440, pp. 25-34, (2006).
[2] Santofimia, M.J., Zhao, L., Petrov, R., Kwakernaak, C., Sloof, W.G. and Sietsma, J., “Microstructural development during the quenching and partitioning process in a newly designed low-carbon steel”, Acta Materialia, Vol. 59, pp. 6059-6068, (2011).
[3] Speer, J.G.,Edmonds, D.V.,Rizzo,F.C. and Matlock, D.K.,“Partitioning of carbon from supersaturated plates of ferrite, with application to steel processing and fundamentals of the bainite transformation”, Current Opinion in Solid-State and Materials Science, Vol. 8, pp. 219-237, (2004).
[4] E. De Moor, S. Lacroix, A.J. Clarke, J. Penning, J.G. Speer,Effect of retained austenite stabilized via quench and partitioning on the strain hardening of martensitic steels. Metall. Mater.Trans. A. 2008, 39, 2586–2589.
[5] N. Fonstein, AdvancedHigh Strength Sheet Steels: PhysicalMetallurgy, Design, Processing, andProperties.2015.
[6] S. Hayami and T. Furukawa, A family of high-strength cold-rolled steels, in Union Carbide Corporation, 1975, pp. 311-321, New York.
[7] K. Lee, Y.R. Im, K. Chin, Effect of Carbon Content on the Microstructure and Transformation Kinetics of Super Bainitic TRIP Steels,Materials Science and Technology Conference, 2008, 1, pp. 1785-93.
[8] L. Wang, J.G. Speer, Quenching and Partitioning Steel Heat Treatment, Metallogr. Microstruct. Anal. 2013, 2, 268–281.
[9] Goladhar MA, principles and users of heat treatment of steels and cast irons. Isfahan, Nash Arkan, 1376. (in Persian)
[10] J. Speer, D. Edmonds, F. Rizzo, D. Matlock, Partitioning of carbon fromsupersaturated plates of ferrite, with application to steel processing and fundamentals of the bainite transformation”, Current Opinion in Solid-State and Materials Science, Vol. 8, pp. 219-237, 2004.
[11] Z. Xiong, P. Jacques, A. Perlade, T. Pardoen, Ductile and intergranular brittle fracture in a two-step quenching and partitioning steel, Scripta Materialia. 2018, 157, 6–9.
[12] P. Xia, I. Sabirov, J. Aldareguia, P. Verleysen, R. Petrov, Mechanical behavior and microstructure evolution of a quenched and partitioned steel during drop weight impact and punch testing. Materials Science & Engineering A. 2018, 737, 18–26.
[13] I. Andersen, O. Grong, "Acta Metall. Mater", 1995, 7, pp. 2673-2688.
[14] Shir Ali A., Hanrabakhsh Rauf A. and Bezazbannai S., 2013, investigation of rapid cooling and segmentation process on a low alloyed medium carbon steel, 2nd international conference and 7th joint conference of Iran Metallurgical Engineering Association and Iranian Casting Scientific Association, Semnan. (in Persian)
[15] Shir Ali A, Hanrabakhsh Rauf A and Bezazbannai S, 2013, microstructure and mechanical properties of a high-carbon and low-alloy steel processed by rapid cooling process and segmentation, Metallurgical and Materials Engineering Quarterly, Volume 26, Number 1. (in Persian)
[16] S. Ebner, C.Suppan, R. Schnitzer, C. Hofer, Microstructure and mechanical properties of a low C steel subjected to bainitic or quenching and partitioning heat treatments. Materials Science & Engineering A. 2018, 735, 1–9.
[17] H. K.D.H. Bhadeshia, R. Honeycombe, Steels: Microstructure and Properties, 3th Edn. Butterworth-Heinemann, Oxford, UK, 2006.
[18] E. Rowland, S. Lyle, The application of MS points to case depth measurement, Trans. ASM 37 27–47, 1946.
[19] Htun, M.S., Kyaw, S.T., Lwin, K.T., 2008. Effect of heat treatment on microstructure and mechanical properties of spring steel. Journal of Metals, Materials and Minerals, Vol. 18, No. 2, pp. 191-197.
[20] A. almasi, A. kian vash, Abolfazl Tutunchi, Effects of Partitioning Time and Temperature on the Microstructure and Mechanical Properties of a High Strength Microalloyed Steel, Metallography, Microstructure, and Analysis, 2021 doi.org/10.1007/s13632-021-00762-6
[21] ASTM Standards, Standard Practice for X-Ray Determination of Retained Austenite in Steel.
[22] W. Hosford,R. M. Caddell, Metal forming: mechanics and metallurgy, Cambridge: Cambridge University Press, 2011.
[23] ASTME 643-84, Standard Test Method for Ball Punch Deformation of Metallic Sheet Material, Annual Book of ASTME Standards, Section 3, Vol. 03.01, pp. 885-888, 1989.
Iranian Journal of Manufacturing Engineering
Volume 9, Issue 7
October 2022
Pages 22-28

Files

Share

How to cite

Statistics