Iranian Journal of Manufacturing Engineering

Iranian Journal of Manufacturing Engineering

Keyword Index
A
  • AA6061-T6 Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
  • ABAQUS Experimental and Numerical investigation of explosive work hardening process on railway frogs [Volume 8, Issue 9, 2021, Pages 23-36]
  • Abrasive powders The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
  • Acoustic transducer Prototyping of piezoceramic-polymer composites using Solution Casting method for use in acoustic Transducers [Volume 8, Issue 5, 2021, Pages 14-22]
  • Additive Manufacturing Computer-aided Porous Structure Implant Design and Analysis using Triply periodic minimal surface [Volume 8, Issue 1, 2021, Pages 46-54]
  • Advanced high strength steel Effect of intercritical annealing temperature and time on the microstructure and mechanical properties of medium Mn advanced high strength steel [Volume 8, Issue 11, 2021, Pages 16-34]
  • AFM Investigation of the effect of different parameters on force in the second phase of two-dimensional nanomanipulation [Volume 8, Issue 2, 2021, Pages 23-31]
  • Age Hardening The effect of H900 and H1150 heat treatment on the machinability of 15-5 PH stainless steel [Volume 8, Issue 12, 2021, Pages 11-20]
  • AISI630 steel, hot turning Experimental investigation of the effects of hot turning parameters on the cutting tool wear and surface roughness of AISI630 hardened stainless steel [Volume 8, Issue 2, 2021, Pages 52-64]
  • AISI O1 Cold work Tool Steel Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
  • Al 2024 Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
  • Al2O3 Nano particle Incorporation of Al2O3 powder for improvement of the mechanical and metallurgical properties of multi-passes friction stir welding of Al 2024 [Volume 8, Issue 3, 2021, Pages 35-46]
  • Aluminum Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
  • Aluminum alloy 5052 Effects of hydrostatic tube cyclic extrusion compression process on the properties of 5052 aluminum alloy [Volume 8, Issue 8, 2021, Pages 38-51]
  • Aluminum alloy . Experimental design The effect of machining parameters of magnetic abrasive finishing on free surface of aluminum alloy [Volume 8, Issue 11, 2021, Pages 63-75]
  • Aluminum alloys Minimizing piston mass of Neuman Esser reciprocating compressors using genetic algorithm [Volume 8, Issue 5, 2021, Pages 30-42]
  • ATI425 alloy Investigation of flow behavior and microstructure modification of ATI425 alloy with initial martensite microstructure in α/β phase and β single phase [Volume 8, Issue 9, 2021, Pages 1-13]
  • Automatic positioning system Automation of sheet metal positioning in stamping die design [Volume 8, Issue 1, 2021, Pages 55-67]
  • AZ31B Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
B
  • Bagasse fibers Manufacturing gypsum composite with short fiber of bagasse (sugarcane wastes) [Volume 8, Issue 4, 2021, Pages 12-18]
  • Brazing Investigation the shear strength and the microstructure of the dissimilar joint of S.S310S to zirconia ceramic using filler without active elements [Volume 8, Issue 5, 2021, Pages 1-13]
  • Brazing Presentation of a new construction methodology and experimental study of the energy absorption of pyramid core sandwich panels [Volume 8, Issue 7, 2021, Pages 10-19]
  • Buckling Determination of stiffness coefficients and buckling strength of composite lattice conical shells using shell fiber path and lattice rib analysis [Volume 8, Issue 7, 2021, Pages 31-42]
  • Burst pressure Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
C
  • Cell size Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
  • Cleaning Experimental study of the plasma electrolyte cleaning using different signal shapes [Volume 8, Issue 8, 2021, Pages 1-11]
  • Clinking process Experimental investigation of the joinability of three-layer aluminum/ polymer/ aluminum composite sheets by the clinching process [Volume 8, Issue 4, 2021, Pages 27-38]
  • CNG fuel tank Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
  • Cold Fluid Experimental Investigation of the Effective Parameters in 7075-T6 Aluminum Machining Process on Surface Roughness Using Minimum Quantity Lubrication (MQL) and Cold Fluid [Volume 8, Issue 6, 2021, Pages 7-14]
  • Composite Pressure Vessel Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
  • Composite Rupture disc Investigating the effect of nonlinear strain path on the mechanical properties of sheet metal to predict burst pressure of composite Rupture disc [Volume 8, Issue 4, 2021, Pages 1-11]
  • Composites Investigating the effect of different variables to reduce delamination due to drilling in composite laminates [Volume 8, Issue 6, 2021, Pages 15-20]
  • Composite shells Determination of stiffness coefficients and buckling strength of composite lattice conical shells using shell fiber path and lattice rib analysis [Volume 8, Issue 7, 2021, Pages 31-42]
  • Constitutive equation Prediction of hot deformation behavior of 304 stainless steel using Johnson-Cook equation [Volume 8, Issue 12, 2021, Pages 34-43]
  • Constitutive equations Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
  • Constraint forces A Force Analysis of Rotary Kiln Elastomers in the Neyzar Qom Cement Company Considering Static, Dynamic, and Thermal Loadings [Volume 8, Issue 6, 2021, Pages 34-40]
  • Corrosion Resistance Investigation of the effect of ultrasonic vibration on the microstructure and mechanical properties of carbon steel in friction drilling process [Volume 8, Issue 7, 2021, Pages 1-9]
  • Creep Evaluation of rotary fatigue bending and creep performance in PLA components during fused deposition modeling [Volume 8, Issue 9, 2021, Pages 60-69]
  • Creep Numerical Investigation of Creep Behavior Turbine blade made of Inconel 939 Superalloy with different Creep Models [Volume 8, Issue 12, 2021, Pages 51-59]
  • Curved Surfaces Evaluation of the defect size in the curved surfaces using digital shearography NDT method [Volume 8, Issue 11, 2021, Pages 54-62]
  • Cutting force The effect of H900 and H1150 heat treatment on the machinability of 15-5 PH stainless steel [Volume 8, Issue 12, 2021, Pages 11-20]
D
  • Damage Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
  • Damage model Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
  • Deformation mechanism Experimental study on stamping of metal/composite laminates reinforced with glass fibers and nanoclay particles [Volume 8, Issue 2, 2021, Pages 1-10]
  • Delamination Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
  • Delamination factor Investigating the effect of different variables to reduce delamination due to drilling in composite laminates [Volume 8, Issue 6, 2021, Pages 15-20]
  • Digital shearography Evaluation of the defect size in the curved surfaces using digital shearography NDT method [Volume 8, Issue 11, 2021, Pages 54-62]
  • Dimensional Tolerance Comparison of Dimensional, Geometrical Tolerances and Surface Integrity in Conventional Drilling and Helical Milling Processes on Steel Multi-layer (Sandwich) Workpiece [Volume 8, Issue 5, 2021, Pages 51-62]
  • Dissimilar welding Dissimilar welding of 5xxx and 7xxx aluminum alloy by self-reacting friction stir welding method [Volume 8, Issue 1, 2021, Pages 1-13]
  • Drilling Comparison of Dimensional, Geometrical Tolerances and Surface Integrity in Conventional Drilling and Helical Milling Processes on Steel Multi-layer (Sandwich) Workpiece [Volume 8, Issue 5, 2021, Pages 51-62]
  • Drilling Investigating the effect of different variables to reduce delamination due to drilling in composite laminates [Volume 8, Issue 6, 2021, Pages 15-20]
  • Drilling Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
  • Dry turning Experimental study and sobol sensitivity analysis in optimizing the effective parameters of dry turning process of aluminum alloy 6061-T6 [Volume 8, Issue 8, 2021, Pages 12-23]
  • Ductile Cast Iron Study of the effect of roller burnishing process parameters on surface roughness and micro hardness of cast iron parts. [Volume 8, Issue 1, 2021, Pages 23-34]
  • Ductile fracture criteria Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process [Volume 8, Issue 8, 2021, Pages 24-37]
  • Duplex stainless steel 2205 Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
  • Dynamic recovery Investigation of flow behavior and microstructure modification of ATI425 alloy with initial martensite microstructure in α/β phase and β single phase [Volume 8, Issue 9, 2021, Pages 1-13]
  • Dynamic recrystallization Investigation of flow behavior and microstructure modification of ATI425 alloy with initial martensite microstructure in α/β phase and β single phase [Volume 8, Issue 9, 2021, Pages 1-13]
  • Dynamics of marine robotics Dynamic modeling and decoupled control of linear and angular velocity for robotic fish [Volume 8, Issue 1, 2021, Pages 35-45]
E
  • E -Fast Investigation of the effect of different parameters on force in the second phase of two-dimensional nanomanipulation [Volume 8, Issue 2, 2021, Pages 23-31]
  • Effective thermal conductivity Microstructure design of heterogeneous material using multisided patch [Volume 8, Issue 2, 2021, Pages 32-40]
  • Electrical Discharge Investigation of aluminum surface properties in surface improvement process by electric discharge method [Volume 8, Issue 3, 2021, Pages 1-8]
  • Electromagnetic flow meter Design and fabrication of electromagnetic arrayed flow meter to measure velocity profiles in a rectangular channel [Volume 8, Issue 12, 2021, Pages 21-33]
  • Electromagnetic pump Optimization of the Lorentz force in an electromagnetic pump by the surface response method with numerical solution of Maxwell equations in three dimensions and comparison with experimental results [Volume 8, Issue 9, 2021, Pages 14-22]
  • Energy absorption Presentation of a new construction methodology and experimental study of the energy absorption of pyramid core sandwich panels [Volume 8, Issue 7, 2021, Pages 10-19]
  • Experimental test Experimental and numerical investigation of laser shock peening effects on residual stresses and fatigue life in hollow plate [Volume 8, Issue 3, 2021, Pages 59-67]
  • Explosive work-hardening Experimental and Numerical investigation of explosive work hardening process on railway frogs [Volume 8, Issue 9, 2021, Pages 23-36]
F
  • Failure Pressure Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
  • Failure zone Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
  • FEM Numerical Investigation of Creep Behavior Turbine blade made of Inconel 939 Superalloy with different Creep Models [Volume 8, Issue 12, 2021, Pages 51-59]
  • Fiber path Determination of stiffness coefficients and buckling strength of composite lattice conical shells using shell fiber path and lattice rib analysis [Volume 8, Issue 7, 2021, Pages 31-42]
  • Fiber twist angle Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
  • Fine-grained material Investigation of the Effect of Backpressure and Friction on Material Flow in the Twist Extrusion Process of 6063 Aluminum Alloy [Volume 8, Issue 6, 2021, Pages 1-6]
  • Finite Element The Effect of Thickness, Welding Metals Sequence and Composition on Residual Stresses in Welding Gas Steel Pipes using LTT filler [Volume 8, Issue 2, 2021, Pages 11-22]
  • Finite Element Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
  • Finite element method Computer-aided Porous Structure Implant Design and Analysis using Triply periodic minimal surface [Volume 8, Issue 1, 2021, Pages 46-54]
  • Finite element method Evaluation of the wear behavior on nanostructure and mechanical characteristics of hydrodynamic sliding bearings [Volume 8, Issue 3, 2021, Pages 20-34]
  • Finite element method A Force Analysis of Rotary Kiln Elastomers in the Neyzar Qom Cement Company Considering Static, Dynamic, and Thermal Loadings [Volume 8, Issue 6, 2021, Pages 34-40]
  • Finite element model Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
  • Finite element simulation Investigation of the Effect of Backpressure and Friction on Material Flow in the Twist Extrusion Process of 6063 Aluminum Alloy [Volume 8, Issue 6, 2021, Pages 1-6]
  • Finite Elements Method Effect of temperature-dependent physical properties on finite element modeling of laser welding of titanium alloy [Volume 8, Issue 10, 2021, Pages 16-27]
  • Flexible Die Support The effect of flexible die support from polymeric foam on the incremental forming of polyethylene sheet [Volume 8, Issue 10, 2021, Pages 38-48]
  • Flexural Strength Experimental study and statistical optimization of fabrication parameters affecting the flexural strength of composite grid-stiffened panels [Volume 8, Issue 11, 2021, Pages 1-15]
  • Flow stress Prediction of hot deformation behavior of 304 stainless steel using Johnson-Cook equation [Volume 8, Issue 12, 2021, Pages 34-43]
  • Foam Density Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
  • Folded cross section Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process [Volume 8, Issue 8, 2021, Pages 24-37]
  • Free surface The effect of machining parameters of magnetic abrasive finishing on free surface of aluminum alloy [Volume 8, Issue 11, 2021, Pages 63-75]
  • Friction drilling Investigation of the effect of ultrasonic vibration on the microstructure and mechanical properties of carbon steel in friction drilling process [Volume 8, Issue 7, 2021, Pages 1-9]
  • Friction stir consolidation Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
  • Friction Stir Welding Incorporation of Al2O3 powder for improvement of the mechanical and metallurgical properties of multi-passes friction stir welding of Al 2024 [Volume 8, Issue 3, 2021, Pages 35-46]
  • Fused deposition modeling (FDM) Evaluation of rotary fatigue bending and creep performance in PLA components during fused deposition modeling [Volume 8, Issue 9, 2021, Pages 60-69]
G
  • Galfenol Design and Fabrication of a Contactless Hybrid Static Magnetostrictive Force-Torque Sensor Using Galfenol [Volume 8, Issue 9, 2021, Pages 50-59]
  • Gap function Evaluation of the wear behavior on nanostructure and mechanical characteristics of hydrodynamic sliding bearings [Volume 8, Issue 3, 2021, Pages 20-34]
  • Gas Turbine Blade Numerical Investigation of Creep Behavior Turbine blade made of Inconel 939 Superalloy with different Creep Models [Volume 8, Issue 12, 2021, Pages 51-59]
  • Genetic Algorithm Minimizing piston mass of Neuman Esser reciprocating compressors using genetic algorithm [Volume 8, Issue 5, 2021, Pages 30-42]
  • Geometrical Parameters Presentation of a new construction methodology and experimental study of the energy absorption of pyramid core sandwich panels [Volume 8, Issue 7, 2021, Pages 10-19]
  • Geometrical Tolerance Comparison of Dimensional, Geometrical Tolerances and Surface Integrity in Conventional Drilling and Helical Milling Processes on Steel Multi-layer (Sandwich) Workpiece [Volume 8, Issue 5, 2021, Pages 51-62]
  • Geometric parameters Computational evaluation of the effect of geometric parameters on the mechanical performance of shape memory alloy stents for use in the breathing systems [Volume 8, Issue 7, 2021, Pages 52-65]
  • Grinding burn Nondestructive detection of Microstructural Changes due to the Grinding Burn Using Electromagnetic Probes [Volume 8, Issue 3, 2021, Pages 9-19]
  • Gurson-Tevergaard-Needleman Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
  • Gypsum based composite Manufacturing gypsum composite with short fiber of bagasse (sugarcane wastes) [Volume 8, Issue 4, 2021, Pages 12-18]
H
  • Hardness Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
  • Hardness Investigation of the Effect of Substrate Material in Nano-indentation Process using Molecular Dynamics Simulation [Volume 8, Issue 10, 2021, Pages 1-15]
  • Heat-affected zone (HAZ) Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
  • Helical Milling Comparison of Dimensional, Geometrical Tolerances and Surface Integrity in Conventional Drilling and Helical Milling Processes on Steel Multi-layer (Sandwich) Workpiece [Volume 8, Issue 5, 2021, Pages 51-62]
  • High Power Diode Laser Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
  • High-temperature Tensile Testing Investigation of effects of the temperature and adding nano-SiO2-particles on high-temperature mechanical properties for the piston aluminum-silicon alloy [Volume 8, Issue 3, 2021, Pages 47-58]
  • HI-LOW Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
  • Hot and warm working Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
  • Hot torsion Prediction of hot deformation behavior of 304 stainless steel using Johnson-Cook equation [Volume 8, Issue 12, 2021, Pages 34-43]
  • Hydrodynamic lubrication Evaluation of the wear behavior on nanostructure and mechanical characteristics of hydrodynamic sliding bearings [Volume 8, Issue 3, 2021, Pages 20-34]
  • Hydrostatic tube cyclic extrusion compression process Effects of hydrostatic tube cyclic extrusion compression process on the properties of 5052 aluminum alloy [Volume 8, Issue 8, 2021, Pages 38-51]
  • Hydroxyapatite Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
I
  • Inconel 939 superalloy Numerical Investigation of Creep Behavior Turbine blade made of Inconel 939 Superalloy with different Creep Models [Volume 8, Issue 12, 2021, Pages 51-59]
  • Incremental Forming The effect of flexible die support from polymeric foam on the incremental forming of polyethylene sheet [Volume 8, Issue 10, 2021, Pages 38-48]
  • Intercritical annealing Effect of intercritical annealing temperature and time on the microstructure and mechanical properties of medium Mn advanced high strength steel [Volume 8, Issue 11, 2021, Pages 16-34]
J
  • Johnson-Cook Prediction of hot deformation behavior of 304 stainless steel using Johnson-Cook equation [Volume 8, Issue 12, 2021, Pages 34-43]
K
  • Kerf Width Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
L
  • Laminated composites Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
  • Laser Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
  • Laser Shock Peening Experimental and numerical investigation of laser shock peening effects on residual stresses and fatigue life in hollow plate [Volume 8, Issue 3, 2021, Pages 59-67]
  • Laser spot welding Experimental investigation of the effects of laser parameters on the strength and size of the weld nugget in laser spot welding of stainless steel sheet 316 [Volume 8, Issue 5, 2021, Pages 23-29]
  • Laser–waterjet hybrid machining Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
  • Laser Welding Effect of temperature-dependent physical properties on finite element modeling of laser welding of titanium alloy [Volume 8, Issue 10, 2021, Pages 16-27]
  • Lattice conical structure Determination of stiffness coefficients and buckling strength of composite lattice conical shells using shell fiber path and lattice rib analysis [Volume 8, Issue 7, 2021, Pages 31-42]
  • Lorentz force Optimization of the Lorentz force in an electromagnetic pump by the surface response method with numerical solution of Maxwell equations in three dimensions and comparison with experimental results [Volume 8, Issue 9, 2021, Pages 14-22]
  • LTT The Effect of Thickness, Welding Metals Sequence and Composition on Residual Stresses in Welding Gas Steel Pipes using LTT filler [Volume 8, Issue 2, 2021, Pages 11-22]
  • LTT Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
M
  • Machining chip Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
  • Machining Parameters The effect of machining parameters of magnetic abrasive finishing on free surface of aluminum alloy [Volume 8, Issue 11, 2021, Pages 63-75]
  • Magnetic abrasive finishing The effect of machining parameters of magnetic abrasive finishing on free surface of aluminum alloy [Volume 8, Issue 11, 2021, Pages 63-75]
  • Magnetic field The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
  • Magnetic flux leakage method Nondestructive detection of Microstructural Changes due to the Grinding Burn Using Electromagnetic Probes [Volume 8, Issue 3, 2021, Pages 9-19]
  • Magnetic permeability Nondestructive detection of Microstructural Changes due to the Grinding Burn Using Electromagnetic Probes [Volume 8, Issue 3, 2021, Pages 9-19]
  • Magnetoelasticity Design and Fabrication of a Contactless Hybrid Static Magnetostrictive Force-Torque Sensor Using Galfenol [Volume 8, Issue 9, 2021, Pages 50-59]
  • Manufacturing Uncertainty Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
  • Mass method Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
  • Mechanical properties Dissimilar welding of 5xxx and 7xxx aluminum alloy by self-reacting friction stir welding method [Volume 8, Issue 1, 2021, Pages 1-13]
  • Mechanical properties Investigation of production process parameters effects on the mechanical properties of Thermex rebar by Taguchi method [Volume 8, Issue 2, 2021, Pages 41-51]
  • Mechanical properties Effect of intercritical annealing temperature and time on the microstructure and mechanical properties of medium Mn advanced high strength steel [Volume 8, Issue 11, 2021, Pages 16-34]
  • Melt Pool Effect of temperature-dependent physical properties on finite element modeling of laser welding of titanium alloy [Volume 8, Issue 10, 2021, Pages 16-27]
  • Metal Injection Molding Synthesis and Investigation of Properties of Polyethylene Oxide Bonding System for Production of High Density 316L Alloy Parts by Metal Injection Molding [Volume 8, Issue 8, 2021, Pages 60-69]
  • Metallurgical Properties Incorporation of Al2O3 powder for improvement of the mechanical and metallurgical properties of multi-passes friction stir welding of Al 2024 [Volume 8, Issue 3, 2021, Pages 35-46]
  • Metal-Nanocomposite Laminates Experimental study on stamping of metal/composite laminates reinforced with glass fibers and nanoclay particles [Volume 8, Issue 2, 2021, Pages 1-10]
  • Microstructure analysis Investigation the shear strength and the microstructure of the dissimilar joint of S.S310S to zirconia ceramic using filler without active elements [Volume 8, Issue 5, 2021, Pages 1-13]
  • Microstructure design Microstructure design of heterogeneous material using multisided patch [Volume 8, Issue 2, 2021, Pages 32-40]
  • Minimum quantity lubrication (MQL) Experimental Investigation of the Effective Parameters in 7075-T6 Aluminum Machining Process on Surface Roughness Using Minimum Quantity Lubrication (MQL) and Cold Fluid [Volume 8, Issue 6, 2021, Pages 7-14]
  • Modification of the Shear Distance Evaluation of the defect size in the curved surfaces using digital shearography NDT method [Volume 8, Issue 11, 2021, Pages 54-62]
  • Modified dynamic materials model Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
  • Molecular dynamic method Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
  • Molecular Dynamics Investigation of the Effect of Substrate Material in Nano-indentation Process using Molecular Dynamics Simulation [Volume 8, Issue 10, 2021, Pages 1-15]
  • Monte Carlo simulation Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
N
  • Nanoclay Particles Experimental study on stamping of metal/composite laminates reinforced with glass fibers and nanoclay particles [Volume 8, Issue 2, 2021, Pages 1-10]
  • Nano-indentation Investigation of the Effect of Substrate Material in Nano-indentation Process using Molecular Dynamics Simulation [Volume 8, Issue 10, 2021, Pages 1-15]
  • Nanomachining Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
  • Nanoparticles Evaluation of the wear behavior on nanostructure and mechanical characteristics of hydrodynamic sliding bearings [Volume 8, Issue 3, 2021, Pages 20-34]
  • Nano polishing The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
  • Navigation module Design and construction of a quadcopter with a new navigation module as a second view for snipers [Volume 8, Issue 8, 2021, Pages 52-59]
  • Non-destructive test Nondestructive detection of Microstructural Changes due to the Grinding Burn Using Electromagnetic Probes [Volume 8, Issue 3, 2021, Pages 9-19]
  • Nonlinear strain path Investigating the effect of nonlinear strain path on the mechanical properties of sheet metal to predict burst pressure of composite Rupture disc [Volume 8, Issue 4, 2021, Pages 1-11]
  • Numerical Solution Optimization of the Lorentz force in an electromagnetic pump by the surface response method with numerical solution of Maxwell equations in three dimensions and comparison with experimental results [Volume 8, Issue 9, 2021, Pages 14-22]
  • Numerical Study Computational evaluation of the effect of geometric parameters on the mechanical performance of shape memory alloy stents for use in the breathing systems [Volume 8, Issue 7, 2021, Pages 52-65]
P
  • Penetration welding The Effect of Thickness, Welding Metals Sequence and Composition on Residual Stresses in Welding Gas Steel Pipes using LTT filler [Volume 8, Issue 2, 2021, Pages 11-22]
  • Penetration welding Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
  • PEO Synthesis and Investigation of Properties of Polyethylene Oxide Bonding System for Production of High Density 316L Alloy Parts by Metal Injection Molding [Volume 8, Issue 8, 2021, Pages 60-69]
  • Piezoceramic Prototyping of piezoceramic-polymer composites using Solution Casting method for use in acoustic Transducers [Volume 8, Issue 5, 2021, Pages 14-22]
  • Piezocomposite Prototyping of piezoceramic-polymer composites using Solution Casting method for use in acoustic Transducers [Volume 8, Issue 5, 2021, Pages 14-22]
  • Piezoelectric Prototyping of piezoceramic-polymer composites using Solution Casting method for use in acoustic Transducers [Volume 8, Issue 5, 2021, Pages 14-22]
  • Piston Minimizing piston mass of Neuman Esser reciprocating compressors using genetic algorithm [Volume 8, Issue 5, 2021, Pages 30-42]
  • Piston aluminum alloy Investigation of effects of the temperature and adding nano-SiO2-particles on high-temperature mechanical properties for the piston aluminum-silicon alloy [Volume 8, Issue 3, 2021, Pages 47-58]
  • PLA Evaluation of rotary fatigue bending and creep performance in PLA components during fused deposition modeling [Volume 8, Issue 9, 2021, Pages 60-69]
  • Plastic strain Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
  • Polylactic Acid Fabrication of polylactic acid / polyethylene glycol/ hydroxyapatite nanoparticles nanocomposite foam by mass porosity method [Volume 8, Issue 9, 2021, Pages 37-49]
  • Polymeric Binder Synthesis and Investigation of Properties of Polyethylene Oxide Bonding System for Production of High Density 316L Alloy Parts by Metal Injection Molding [Volume 8, Issue 8, 2021, Pages 60-69]
  • Polymeric Sheet The effect of flexible die support from polymeric foam on the incremental forming of polyethylene sheet [Volume 8, Issue 10, 2021, Pages 38-48]
  • Porous Implant Computer-aided Porous Structure Implant Design and Analysis using Triply periodic minimal surface [Volume 8, Issue 1, 2021, Pages 46-54]
  • Predicting burst pressure Investigating the effect of nonlinear strain path on the mechanical properties of sheet metal to predict burst pressure of composite Rupture disc [Volume 8, Issue 4, 2021, Pages 1-11]
  • Pyramidal lattice structures Presentation of a new construction methodology and experimental study of the energy absorption of pyramid core sandwich panels [Volume 8, Issue 7, 2021, Pages 10-19]
Q
  • Quadcopter Design and construction of a quadcopter with a new navigation module as a second view for snipers [Volume 8, Issue 8, 2021, Pages 52-59]
R
  • Railway frog Experimental and Numerical investigation of explosive work hardening process on railway frogs [Volume 8, Issue 9, 2021, Pages 23-36]
  • Railway switches Experimental and Numerical investigation of explosive work hardening process on railway frogs [Volume 8, Issue 9, 2021, Pages 23-36]
  • Rebar Investigation of production process parameters effects on the mechanical properties of Thermex rebar by Taguchi method [Volume 8, Issue 2, 2021, Pages 41-51]
  • Recycling Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
  • Regression Model Experimental study of the shunting effect on tensile-shear strength of resistance spot welds in AA2219 sheets [Volume 8, Issue 12, 2021, Pages 44-50]
  • Reliability Reliability Analysis of Failure in Composite Pressure Vessels [Volume 8, Issue 4, 2021, Pages 50-61]
  • Reshaping Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process [Volume 8, Issue 8, 2021, Pages 24-37]
  • Residual Stress Investigation of aluminum surface properties in surface improvement process by electric discharge method [Volume 8, Issue 3, 2021, Pages 1-8]
  • Residual Stress Experimental and numerical investigation of laser shock peening effects on residual stresses and fatigue life in hollow plate [Volume 8, Issue 3, 2021, Pages 59-67]
  • Residual stresses The Effect of Thickness, Welding Metals Sequence and Composition on Residual Stresses in Welding Gas Steel Pipes using LTT filler [Volume 8, Issue 2, 2021, Pages 11-22]
  • Residual stresses Experimental and Numerical Comparison of the Effects of Phase Trasformation Changes and Asymmetric Welding on Residual Stresses in Gas Pipe Welding Using LTT Filler [Volume 8, Issue 4, 2021, Pages 39-49]
  • Resistance spot weld Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model [Volume 8, Issue 7, 2021, Pages 43-51]
  • Resistance spot welding Experimental study of the shunting effect on tensile-shear strength of resistance spot welds in AA2219 sheets [Volume 8, Issue 12, 2021, Pages 44-50]
  • Robotic fish Dynamic modeling and decoupled control of linear and angular velocity for robotic fish [Volume 8, Issue 1, 2021, Pages 35-45]
  • Robotic fish motion control Dynamic modeling and decoupled control of linear and angular velocity for robotic fish [Volume 8, Issue 1, 2021, Pages 35-45]
  • Roller Burnishing Study of the effect of roller burnishing process parameters on surface roughness and micro hardness of cast iron parts. [Volume 8, Issue 1, 2021, Pages 23-34]
  • Roll Forming Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process [Volume 8, Issue 8, 2021, Pages 24-37]
  • Rotary fatigue bending Evaluation of rotary fatigue bending and creep performance in PLA components during fused deposition modeling [Volume 8, Issue 9, 2021, Pages 60-69]
  • Rotary kiln A Force Analysis of Rotary Kiln Elastomers in the Neyzar Qom Cement Company Considering Static, Dynamic, and Thermal Loadings [Volume 8, Issue 6, 2021, Pages 34-40]
  • Rotational Speed The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
S
  • Seamless tube Investigation of microstructure and hardness of recycled aluminum seamless tube using friction stir consolidation [Volume 8, Issue 11, 2021, Pages 35-42]
  • Second phase Investigation of the effect of different parameters on force in the second phase of two-dimensional nanomanipulation [Volume 8, Issue 2, 2021, Pages 23-31]
  • Sensitivity analysis Investigation of effects of the temperature and adding nano-SiO2-particles on high-temperature mechanical properties for the piston aluminum-silicon alloy [Volume 8, Issue 3, 2021, Pages 47-58]
  • Sensitivity analysis Experimental study and sobol sensitivity analysis in optimizing the effective parameters of dry turning process of aluminum alloy 6061-T6 [Volume 8, Issue 8, 2021, Pages 12-23]
  • Sensor Design and Fabrication of a Contactless Hybrid Static Magnetostrictive Force-Torque Sensor Using Galfenol [Volume 8, Issue 9, 2021, Pages 50-59]
  • Severe plastic deformation Investigation of the Effect of Backpressure and Friction on Material Flow in the Twist Extrusion Process of 6063 Aluminum Alloy [Volume 8, Issue 6, 2021, Pages 1-6]
  • Severe plastic deformation Effects of hydrostatic tube cyclic extrusion compression process on the properties of 5052 aluminum alloy [Volume 8, Issue 8, 2021, Pages 38-51]
  • Shape memory alloy stent Computational evaluation of the effect of geometric parameters on the mechanical performance of shape memory alloy stents for use in the breathing systems [Volume 8, Issue 7, 2021, Pages 52-65]
  • Shear strength test Investigation the shear strength and the microstructure of the dissimilar joint of S.S310S to zirconia ceramic using filler without active elements [Volume 8, Issue 5, 2021, Pages 1-13]
  • Sheet hydroforming Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
  • Short fibers Manufacturing gypsum composite with short fiber of bagasse (sugarcane wastes) [Volume 8, Issue 4, 2021, Pages 12-18]
  • Shunting effect Experimental study of the shunting effect on tensile-shear strength of resistance spot welds in AA2219 sheets [Volume 8, Issue 12, 2021, Pages 44-50]
  • Single crystal copper Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
  • Sintering Synthesis and Investigation of Properties of Polyethylene Oxide Bonding System for Production of High Density 316L Alloy Parts by Metal Injection Molding [Volume 8, Issue 8, 2021, Pages 60-69]
  • Slitting method Experimental and numerical investigation of laser shock peening effects on residual stresses and fatigue life in hollow plate [Volume 8, Issue 3, 2021, Pages 59-67]
  • Sniper Design and construction of a quadcopter with a new navigation module as a second view for snipers [Volume 8, Issue 8, 2021, Pages 52-59]
  • Sobol sensitivity analysis Mathematical Modeling, Sobol Sensitivity Analysis and Optimization of Main Parameters in Drilling of E-glass/epoxy Laminated Composites [Volume 8, Issue 11, 2021, Pages 43-53]
  • Stamping Process Experimental study on stamping of metal/composite laminates reinforced with glass fibers and nanoclay particles [Volume 8, Issue 2, 2021, Pages 1-10]
  • Statistical-experimental analysis Experimental study and statistical optimization of fabrication parameters affecting the flexural strength of composite grid-stiffened panels [Volume 8, Issue 11, 2021, Pages 1-15]
  • Strain-rate sensitivity coefficient map Construction of constitutive equations, modified dynamic materials model and strain-rate sensitivity coefficient map for investigation of hot and warm working instability of 2205 duplex stainless steel [Volume 8, Issue 12, 2021, Pages 1-10]
  • Substrate material Investigation of the Effect of Substrate Material in Nano-indentation Process using Molecular Dynamics Simulation [Volume 8, Issue 10, 2021, Pages 1-15]
  • Surface alloying Investigation of aluminum surface properties in surface improvement process by electric discharge method [Volume 8, Issue 3, 2021, Pages 1-8]
  • Surface Response Methodology Study of the effect of roller burnishing process parameters on surface roughness and micro hardness of cast iron parts. [Volume 8, Issue 1, 2021, Pages 23-34]
  • Surface roughness Study of the effect of roller burnishing process parameters on surface roughness and micro hardness of cast iron parts. [Volume 8, Issue 1, 2021, Pages 23-34]
  • Surface roughness Experimental investigation of the effects of hot turning parameters on the cutting tool wear and surface roughness of AISI630 hardened stainless steel [Volume 8, Issue 2, 2021, Pages 52-64]
  • Surface roughness Experimental Investigation of the Effective Parameters in 7075-T6 Aluminum Machining Process on Surface Roughness Using Minimum Quantity Lubrication (MQL) and Cold Fluid [Volume 8, Issue 6, 2021, Pages 7-14]
  • Surface roughness Experimental study and sobol sensitivity analysis in optimizing the effective parameters of dry turning process of aluminum alloy 6061-T6 [Volume 8, Issue 8, 2021, Pages 12-23]
  • Surface roughness Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
  • Surface roughness The effect of H900 and H1150 heat treatment on the machinability of 15-5 PH stainless steel [Volume 8, Issue 12, 2021, Pages 11-20]
  • Surface smoothness The Effects of Angular Velocity and Combination of AIO2 and SiC Abrasive Particle by Use of NMAF Method [Volume 8, Issue 6, 2021, Pages 26-33]
  • Surface Transformation Hardening Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
T
  • T6-7075Aluminum Experimental Investigation of the Effective Parameters in 7075-T6 Aluminum Machining Process on Surface Roughness Using Minimum Quantity Lubrication (MQL) and Cold Fluid [Volume 8, Issue 6, 2021, Pages 7-14]
  • Taguchi Experimental study of the plasma electrolyte cleaning using different signal shapes [Volume 8, Issue 8, 2021, Pages 1-11]
  • Taguchi method Investigation of production process parameters effects on the mechanical properties of Thermex rebar by Taguchi method [Volume 8, Issue 2, 2021, Pages 41-51]
  • Taguchi method Investigation and optimization of parameters affecting surface roughness in single crystal copper nanomachining process using molecular dynamics method [Volume 8, Issue 10, 2021, Pages 49-60]
  • Tail-actuated robots Dynamic modeling and decoupled control of linear and angular velocity for robotic fish [Volume 8, Issue 1, 2021, Pages 35-45]
  • Tensile-shear strength Experimental study of the shunting effect on tensile-shear strength of resistance spot welds in AA2219 sheets [Volume 8, Issue 12, 2021, Pages 44-50]
  • Thermex Investigation of production process parameters effects on the mechanical properties of Thermex rebar by Taguchi method [Volume 8, Issue 2, 2021, Pages 41-51]
  • Thickness Distribution The effect of flexible die support from polymeric foam on the incremental forming of polyethylene sheet [Volume 8, Issue 10, 2021, Pages 38-48]
  • Thickness strain Microstructural Studies and Mechanical Properties of Hydroforming Process of AZ31B Magnesium and AA 2024 Aluminum Alloys Sheets at Elevated Temperatures [Volume 8, Issue 10, 2021, Pages 39-48]
  • Ti60 Titanium Alloy Effect of temperature-dependent physical properties on finite element modeling of laser welding of titanium alloy [Volume 8, Issue 10, 2021, Pages 16-27]
  • Tool Wear Experimental investigation of the effects of hot turning parameters on the cutting tool wear and surface roughness of AISI630 hardened stainless steel [Volume 8, Issue 2, 2021, Pages 52-64]
  • Triply Periodic Minimal Surface Computer-aided Porous Structure Implant Design and Analysis using Triply periodic minimal surface [Volume 8, Issue 1, 2021, Pages 46-54]
  • Tube Effects of hydrostatic tube cyclic extrusion compression process on the properties of 5052 aluminum alloy [Volume 8, Issue 8, 2021, Pages 38-51]
  • Twist extrusion process Investigation of the Effect of Backpressure and Friction on Material Flow in the Twist Extrusion Process of 6063 Aluminum Alloy [Volume 8, Issue 6, 2021, Pages 1-6]
  • Type-IV composite tank Numerical simulation of CNG fuel tank behavior made of epoxy/glass composite in design mode considering constant and variable thicknesses under burst pressure test [Volume 8, Issue 7, 2021, Pages 20-30]
U
  • Ultrasonic Vibration Investigation of the effect of ultrasonic vibration on the microstructure and mechanical properties of carbon steel in friction drilling process [Volume 8, Issue 7, 2021, Pages 1-9]
V
  • Velocity profile measurement Design and fabrication of electromagnetic arrayed flow meter to measure velocity profiles in a rectangular channel [Volume 8, Issue 12, 2021, Pages 21-33]
  • Vickers indentation Investigation of aluminum surface properties in surface improvement process by electric discharge method [Volume 8, Issue 3, 2021, Pages 1-8]
W
  • Waterjet Effect of machining parameters on heat-affected zone and kerf width in hybrid laser- waterjet process [Volume 8, Issue 10, 2021, Pages 28-37]
  • Wear resistance Investigation of the effect of surface transformation hardening by high power diode laser on the microstructure, hardness and wear behavior of AISI O1 cold work tool steel [Volume 8, Issue 1, 2021, Pages 14-22]
  • Weld strength Experimental investigation of the effects of laser parameters on the strength and size of the weld nugget in laser spot welding of stainless steel sheet 316 [Volume 8, Issue 5, 2021, Pages 23-29]